ルールシェルの編集オプション

ルールシェルには2つの断面形状があります。1番目の断面形状の端点は大きなホットスポットによって区別されます。これはシェルの基部高さを表します。

以下に断面形状の編集機能の一部を示します。

断面形状を継続[ダンメンケイジョウヲケイゾク]

例えば、直線断面形状を拡張してシェルの端の幅を拡大します。

https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//ContinueProfileRuled.png     https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//ContinueProfileRuled2.png

辺を湾曲[ヘンヲワンキョク]

https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//CurveEdgeRuled1.png     https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//CurveEdgeRuled2.png

断面形状を移動[ダンメンケイジョウヲイドウ]

このコマンドを使用すると、断面形状を新しい位置に合わせてその平面内で水平/垂直方向に移動できます。

https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//DragProfile1.png     https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//DragProfile2.png

断面形状を回転[ダンメンケイジョウヲカイテン]

これらのコマンドは、選択した断面形状を空間で回転させるために使用します。

https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//MirrorShell1.png     https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//MirrorShell2.png

断面形状を高度変更[ダンメンケイジョウヲコウドヘンコウ]

断面形状の平面全体を垂直方向に移動します。

https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//ElevateProfile.png     https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//ElevateProfile2.png

断面形状を水平に移動[ダンメンケイジョウヲスイヘイニイドウ]

断面形状面を水平に移動します。

https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//DragProfileHoriz1.png     https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//DragProfileHoriz2.png

断面形状面を回転[ダンメンケイジョウメンヲカイテン]

https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//TurnPlane1.png 

回転する点をクリックして入力します。次に、カーソルを移動して回転方向を定義し、クリックして終了します。

https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//TurnPlane100072.png   https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//TurnPlane2.png   https://helpcenter.graphisoft.com/jp/wp-content/uploads/sites/3/archicad-23-solo-reference-guide//TurnPlane3.png