Parameter |
Short Description |
Long Description |
|
Edge Surface |
Name of Surface assigned to Wall edges. |
Lists the Wall’s default edge surface (as defined in its Building Material). Not listed for composite Walls. To list all Surfaces, including custom ones and those of composite elements, use a Surface-type list (e.g. All Finishes).
|
|
Inside Slant Angle |
Angle of a slanted Wall from the perpendicular to its Inside Face. |
|
|
Outside Slant Angle |
Angle of a slanted Wall from the perpendicular to its Outside Face. |
Same as the General "Slant Angle" parameter |
|
Wall Geometry Method |
Uniform, Trapezoid or Polygonal. |
|
|
Wall Air Skin Thickness |
Thickness of Wall skin whose structure is defined as “Air skin” |
Air Skin is defined at Options > Project Preferences > Calculation Units & Rules. |
|
Analytic Surface Area of Openings on the Inside Face |
Surface Area of all Wall Openings (windows, doors, empty Openings) on the Wall’s Inside Face. |
Surface calculation is based on hole that results from cutting the GDL Openings out of the Wall. |
|
Analytic Surface Area of Openings on the Outside Face |
Surface Area of all Wall Openings (windows, doors, empty Openings) on the Wall’s Outside Face. |
Surface calculation is based on hole that results from cutting the GDL Openings out of the Wall. |
|
Analytic Volume of Openings in Wall |
Volume of all Wall Openings (windows, doors, empty Openings). |
Volume calculation based on hole that results from cutting the GDL Openings out of the Wall. Does not take SEO’s into account. |
|
Area of the Wall |
Area of the horizontal cross section of the Wall element, as it is displayed on the Floor Plan. |
Area can vary depending on its Floor Plan Projection settings (e.g. Cut Only vs. Projected with Overhead). Wall intersections have no effect on the perimeter value. |
|
Combined Width of doors in Wall |
Sum of the nominal widths (as defined in Door Settings) of all doors placed in the Wall. |
|
|
Combined Width of windows in wall |
Sum of the nominal widths (as defined in Window Settings) of all windows placed in the Wall |
|
|
Conditional Length of the Wall on Inside Face |
Length of Wall along its Inside Face - this Length may be conditioned on a defined Calculation Rule. |
Condition: Subtracts the Length of any Openings that exceed a given Length, as defined in Options > Project Preferences > Calculation Units & Rules (“Reduce Wall Length by…”). |
g |
Conditional Length of the Wall on Outside Face |
Length of Wall along its Inside Face - this Length may be conditioned on a defined Calculation Rule. |
Condition: Subtracts the Length of any Openings that exceed a given Length, as defined in Options > Project Preferences > Calculation Units & Rules (“Reduce Wall Length by…”). |
|
Conditional Surface Area on the Inside Face |
Surface Area of Wall on its Inside Face - this area may be conditioned on a defined Calculation Rule. |
Condition: Subtracts the surface of any Openings that exceed a given area as defined in Options > Project Preferences > Calculation Units & Rules (“Reduce Wall surface by…”). Reduced by trims and SEO’s. |
|
Conditional Surface Area on the Outside Face |
Surface Area of Wall on its Outside Face - this area may be conditioned on a defined Calculation Rule. |
Condition: Subtracts the surface of any Openings that exceed a given area as defined in Options > Project Preferences > Calculation Units & Rules (“Reduce Wall surface by…”). Reduced by trims and SEO’s. |
|
Conditional Wall Skin Volume on the Inside Face |
Volume of skin on the Wall’s Inside Face - this Volume may be conditioned on a defined Calculation Rule. |
Condition: subtracts the Volume of any Openings that exceed a given size, as defined in Options > Project Preferences > Calculation Units & Rules (“Reduce Wall Volume by…”). Reduced by trims and SEO’s. |
|
Conditional Wall Skin Volume on the Outside Face |
Volume of skin on the Wall’s Outside Face - this Volume may be conditioned on a defined Calculation Rule. |
Condition: subtracts the Volume of any Openings that exceed a given size, as defined in Options > Project Preferences > Calculation Units & Rules (“Reduce Wall Volume by…”). Reduced by trims and SEO’s. |
|
End Thickness of the Wall |
End thickness of trapezoid Wall. |
Second thickness, assigned in Wall Settings to a trapezoid Wall. |
|
Gross Surface Area of the wall on the Inside Face |
Gross Surface Area of the Wall - including the surfaces of any Openings - on the Inside Face. |
Reduced by trims. SEO’s are ignored. |
|
Gross Surface Area of the wall on the Outside Face |
Gross Surface Area of the Wall - including the surfaces of any Openings - on the Outside Face. |
Reduced by trims. SEO’s are ignored. |
|
Inside Face Surface |
Name of the surface assigned to the Wall’s Inside Face. |
|
|
Length of Reference Line |
Length of the Wall’s Reference Line. |
|
|
Length of the Wall at the center |
Length of the Wall, as measured from end to end along Wall’s centerline. |
|
|
Length of the Wall on Inside Face |
Length of the Wall, as measured from end to end along Wall’s Inside Face. |
|
|
Length of the Wall on the Outside Face |
Length of the Wall, as measured from end to end along Wall’s Outside Face. |
|
|
Maximum height of the Wall |
Height of Wall at its highest point. |
Roof crops are considered. Trims and SOE's are ignored. |
|
Maximum Height of the Wall Skin on Inside Face |
Height of Wall skin, at its highest point, on the Wall’s Inside Face. |
Roof crops are considered. Trims and SOE's are ignored. |
|
Maximum Height of the Wall Skin on Outside Face |
Height of Wall skin, at its highest point, on the Wall’s Outside Face. |
Roof crops are considered. Trims and SOE's are ignored. |
|
Minimum Height of the Wall Skin on Inside Face. |
Height of Wall skin, at its lowest point, on Wall’s Inside Face. |
Roof crops are considered. Trims and SOE's are ignored. |
|
Minimum Height of the Wall Skin on Outside Face |
Height of Wall skin, at its lowest point, on the Wall’s Outside Face. |
Roof crops are considered. Trims and SOE's are ignored. |
|
Net Surface Area of the edges |
Sum of the areas of all Wall edges. Reduced by trims and Solid Element Operations. |
|
|
Net Surface Area on the Inside Face |
Surface Area of the Wall on the Inside Face. |
Reduced by Openings, trims and Solid Element Operations. |
|
Net Surface Area on the Outside Face |
Surface Area of the Wall on the Outside Face. |
Reduced by Openings, trims and Solid Element Operations. |
|
Number of Intersecting Columns |
Number of Columns that intersect the Wall |
|
|
Number of Doors in Wall |
Number of Door elements in the Wall |
|
|
Number of Holes (Number of Empty Openings) |
Number of Empty Opening Objects in the Wall |
|
|
Number of Windows in Wall |
Number of Window elements in the Wall |
|
|
Outside Face Surface |
Name of the surface assigned to the Wall’s Outside Face. |
|
|
Reference Line location |
As defined in Wall Settings (Outside Face, Inside Face or Center). |
For composite Walls: can also be Core Outside, Core Inside or Core Center. |
|
Thickness of the Wall (Obsolete) |
Obsolete. See General Thickness field. |
|
|
Wall Skin Thickness on the Inside Face |
For Composite Walls: Thickness of the skin on the Wall’s Inside Face. |
Each skin thickness is defined in Options > Element Attributes > Composite Structures. |
|
Wall Skin Thickness on the Outside Face |
For Composite Walls: Thickness of the skin on the Wall’s Outside Face. |
Each skin thickness is defined in Options > Element Attributes > Composite Structures. |
|
Wall Skin Volume on the Inside Face |
Net Volume of the skin on the Wall’s Inside Face. |
Subtracts Volumes of Openings within the skin Reduced by trims and SEO’s. |
|
Wall Skin Volume on the Outside Face |
Net Volume of the skin on the Wall’s Outside Face. |
Subtracts Volumes of Openings within the skin Reduced by trims and SEO’s. |
|
Wall Slant Type |
Straight, Slanted, or Double-slanted. |
As defined in Wall Settings, Geometry and Positioning Panel |
|
Wall Listing Parameters
Parameter
Short Description
Long Description
Curtain Wall Frame Slant Angle
Frame's slant angle in the plane of the Curtain Wall
E.g. 0 or 90 degrees for orthogonally positioned frames, other angles for diagonal ...
Parameter
Short Description
Long Description
Curtain Wall Pattern Angle
...
Parameter
Short Description
Long Description
Length
Length parameter of the Accessory
Measured along the plane of the Curtain Wall
Accessory Class
System or Custom
...