Creating Zones

In Zone Settings, customize the parameters of your zone - such as its name, its category, its height, and the content of its zone stamp. Then you are ready to define the zone shape, either on the Floor Plan or in the 3D Window.

The bottom of every Zone (like other elements) is linked to its Home Story; you can also top-link the Zone to any story above it in the project. As needed, define offsets from its top link or Home Story; this will affect the Zone height. Alternatively, just enter a fixed Zone height, without a top link.

See Zone Tool Settings, Home Story and Define Top Link for Wall, Column, Zone or Stair.

The Zone definition methods are represented by the three icons in the Info Box.

You can either:

manually draw the contour of a zone (using the Polyline, Rectangular or Rotated Rectangular Methods); or

let ARCHICAD automatically recognize a zone surrounded by bordering elements (using one of the two Automatic Recognition methods):

//helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/ZoneInfoBox.png.

See Automatic Recognition Methods.

Note: Columns cannot serve as the enclosing border of a zone. However, you can choose whether the area covered by the column should be included when calculating Zone area and volume.

See also Relation to Zones.

Manual Methods

//helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/ZonePolygon.png 

Use one of the manual methods when your Zone’s boundary is not clearly surrounded by elements (e.g. when doing space planning).

1.Activate the Zone tool.

2.Do one of the following:

Draw a polyline (as you would for any other polygon) by clicking at every corner of the zone; or

Use the rectangular/rotated rectangular methods to draw a rectangle.

3.Click with the appearing Hammer cursor to define the location of the Zone Stamp. (The Zone Stamp does not necessarily have to be placed inside the Zone polygon.)

You can edit a polygonal zone graphically by selecting it and using the pet palette commands.

See Edit Zone Polygon.

Automatic Recognition Methods

//helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/ZoneAutomatic.png 

Both automatic recognition methods, Inner Edge and Reference Line, are based on the fact that most Zones are surrounded by Walls and the only openings in them are Doors and Windows.

If you choose the Inner Edge method, ARCHICAD will always define the zone area by the inner edges of walls.

If you choose the Reference Line method, ARCHICAD considers the reference lines of the walls as the boundaries of the zone.

Note: In case of a slanted or complex wall, the Reference Line method will not consider the wall’s reference line, but rather its inner edge.

Note: To view such a Zone in 2D as extending to the Reference Line, select the Zone and switch its “Zone Polygon Area” control to “Gross” in Zone Settings.

See “Zone Polygon” at Zone Name and Positioning Panel.

Exclude a Wall as a Zone Boundary

By default, the Relation to Zones setting in the Model Panel of Wall Settings is set to “Zone Boundary.”

This means that all walls enclosing a closed space are considered zone boundaries by default.

To exclude any wall as a zone boundary, just change the Relation to Zones setting to No Effect on Zones.

See also Relation to Zones.

Zone Reference Point

If you place the Zone Stamp with one of the automatic recognition methods, a cross appears inside the Zone at the location that you first clicked to define the Zone’s area. This cross indicates the reference point of the Zone.

//helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/ZoneCrossPoint.png 

This point is used as the starting point of boundary recognition for subsequent updating actions.

Edit Zone Polygon

Use the familiar pet palette commands to edit the zone polygon.

See Reshaping Polygons and Chained Elements, and Offset All Edges.

Offset Edge - Fixed Area

Use this pet palette command to offset the clicked edge in such a way that the original Zone area does not change. This is useful if you are doing space planning based on defined areas.

In this example, you offset the right side of the zone - and the shape is automatically constrained so that the area stays constant (as seen in the tracker):

//helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/FixedArea1.png 

//helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/FixedArea2.png 

//helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/FixedArea3.png 

Create a Manual Zone Boundary

If the Zone has openings that are not Doors or Windows, ARCHICAD will continue searching for boundaries outside the spatial unit that you wished to identify as a Zone. In this case, the result may not be what you expect (see figure, below right).

//helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/Zonerecog_OK.png     //helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/Zonerecogwrong.png

In this case, close the Zone by:

using the Polygon method

place an Empty Opening Door object into the Wall which is the same height as the Wall - the Wall is not shown in 2D, but it does serve as a Zone Boundary

drawing a line to serve as a Zone Boundary

//helpcenter.graphisoft.com/wp-content/uploads/ac22_help/040-elementsvb/ZoneStampInOut.png 

You can draw a Line, Arc or Spline to serve as a zone boundary if you check the Zone Boundary checkbox in its Line Settings dialog boxes.

If your desired zone boundaries also encompass freestanding shapes or walls, you may get a warning message when clicking to place the zone stamp. In this case, you must click closer to the bounding elements. Then the zone will be created correctly.

Related Topics:

Updating Zones

Relation to Zones

Calculating Zone Area and Zone Volume

  • Was this Helpful ?
  • YesNo
Relevant topics
Zones Tab Page
The first tab on top of the Setup List Schemes dialog box opens the Zones tab page.   Check individual boxes to filter the list by Zone categories; or check All to use all categories. You can further filter zones using the checkboxes and options under Zone Number Field at the upper ...
Display Zones and Zone Info
In the 3D view, you have the option to display 3D Zones (defined in ARCHICAD). With Zones displayed: •you can access Zone data •you can show the building’s functional areas, even in a conceptual model whose building envelope is not yet in place 1.Open the menu from the left ...