Graphical Editing of Stair Scheme

The following functions let you adjust overall Stair geometry on the Floor Plan, without having to use Edit mode.

Rearrange Steps

Use this pet palette command to graphically rearrange the symmetry of a U-shaped stair:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/Rearrange1.png     https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/Rearrange2.png

Edit Stair Baseline

The Stair Baseline is created during input. Use Stair Settings or the Info Box to set the Baseline position and any offset (either before or after input).

See also Stair Baseline.

You can edit the Stair Baseline in any window (regardless of Edit mode).

To show/hide the Stair Baseline on the Floor Plan, turn on View > On-Screen View Options > Stair Baselines.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/StairBaselineShow.png 

Use the pre-selection highlight tag to make sure you select the Baseline (not the Boundary).

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/EditStairBaseline.png 

Baseline editing changes the overall Stair geometry, including the Walking Line.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/EditStairBaseline1.png   https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/EditStairBaseline2.png

Walking Line Follows Baseline Editing

Continue Stair

To continue a Stair Baseline (in Edit mode or in a model view), use the Continue Stair command from the selected Baseline’s pet palette.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/ContinueStair.png 

Edit Stair Boundary

Select any part of the Boundary to highlight it.

You can edit the Stair Boundary in any window (regardless of Edit mode).

Use the TAB button and the pre-selection highlight to make sure you select the Boundary, not the Baseline.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/EditStairBoundary2.png 

Edit the Stair boundary graphically, using the same pet palette commands as when editing a Fill.

Boundary editing changes the outer shape of the Stair, but the Walking Line and Baseline stay put.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/EditBoundaryFP.png   https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/EditBoundaryFP2.png

Edit Stair Boundary (Walking Line Unaffected)

Show/Hide Boundary Segment on Floor Plan

For any selected Stair segment, use the Boundary Segment Settings pet palette command to open this dialog box.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/BoundarySegmentSettings.png   https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/BoundarySegmentSettingsDB.png

Show or hide the selected segment (or apply to all or other Stair segments) as needed.

For example: you can add two nodes to a Stair segment, then hide the Stair Boundary between those two points.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/Hideboundarysegment1.png   https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/Hideboundarysegment2.png

Insert Two Nodes to Create New Stair Segment... Then Select and Hide Segment

See also Hide Any Edge of a Single Tread.

Edit Stair Boundary - Example

In this example, you can edit the Stair boundary to cut out enough room for a protruding Wall segment.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/EditStairBoundary1.png 

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/EditStairBoundary3.png 

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-25/040_elementsvb/EditStairBoundary3D.png 

  • Was this Helpful ?
  • YesNo
Relevant topics
Graphical Editing of Shells
In Floor Plan, Section and 3D view, a wide range of editing possibilities are available for the Shell. Select your Shell and try out the pet ...
Graphical Editing of MEP Elements
•For any selected MEP element, use the Pet Palette commands to edit the MEP element graphically. •MEP-specific editing commands are available in the Floor Plan and 3D window. •When you edit a selected MEP element, certain parameters of connected (though unselected) MEP ...