Create Opening

1.Activate the Opening tool.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/OpeningIcon.png 

2.In Opening Settings or the Info Box, define the Opening’s basic geometry, shape and anchor point, as needed. (Settings are described in detail below.)

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/OpeningDefaultSettings.png 

3.Hover over the associated element (e.g. Wall) into which to place the opening. The pre-placement highlight indicates the geometry of the Opening and its associated element.

If the cursor is above several potential associated elements, use Tab to cycle the highlight among them.

Note: Opening geometry is measured relative to its associated element, and moves along with it.

4.Click once or twice to place the Opening, depending on its Orientation (see below): Aligned, Vertical, Horizontal or Custom.

Orientation

In the Info Box, the Orientation defines the Opening extrusion relative to the associated element.

Aligned (default)

Click once to place an Opening that is perpendicular to the host element’s reference line or plane. The “Aligned” Opening is automatically placed in the most logical direction depending on the host:

Opening in a Slab or Mesh is vertical

Opening in a straight Wall or Beam is horizontal

Opening in a slanted Wall is perpendicular

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/AlignedOpenings.png 

An Opening placed with the Aligned method remains connected to the host element’s reference line or plane.

Vertical

Click once to place a vertical Opening:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/VerticalOpenings.png 

Horizontal

Click once to place the horizontal Opening, then click again to define extrusion direction:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/HorizontalOpenings.png    https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/HorizontalAngledOpening.png

Custom

Drag, mirror or rotate an existing Opening into any position.

Available for a selected, existing Opening. (Not available as default input method.)

You can change a selected Custom-oriented Opening, then change its orientation to Aligned, Vertical or Horizontal. However, the previous Custom orientation is now lost.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/OpeningCustom.png 

Infinite or Limited Opening

By default, an Opening extends infinitely - as set at the Limits option in Info Box or Opening Settings.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/InfiniteOpening.png 

An “infinite” Opening means that its length does not depend on the cut element’s geometry: if Wall thickness is increased, the Opening still cuts through it.

An Opening can also be defined as limited on one or both sides.

See Use Limited Opening to Create Niche or Recess.

Anchor Point

Position the Opening’s Anchor Point at any of the 9 points on the bounding rectangle.

In 3D, the blue extrusion vector indicates the anchor point’s position.

The anchor remains fixed when you numerically resize the Opening dimensions.

When the Opening is graphically stretched, its centerpoint remains fixed - regardless of the Anchor Point.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/AnchorPointOpening.png 

Opening Elevation

The Opening’s elevation is measured from the associated element’s Home Story to the Opening’s   Anchor point. This is the anchor height value.

In 3D: Click to place the opening graphically at any elevation.

On Floor Plan:

Opening’s anchor height in a vertical element (e.g. Wall) is measured to the associated element’s home story.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/WallOpeningFP.png 

When placing an Opening placed in a Beam, anchor height is indicated from the story above.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/OpeningBeamFP.png 

For an Opening placed in a Slab or Mesh: anchor height follows the elevation of the host element.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/040_elementsvb/OpeningSlabFP.png 

  • Was this Helpful ?
  • YesNo
Relevant topics
Use Limited Opening to Create Niche or Recess
A limited Opening can be used, for example, as a Wall Niche or a Slab Recess. Limit One Side 1.In Opening Settings or the Info Box, choose Limit One Side.   2.Click on the associated element into which to place the opening. 3.Move the eyeball cursor to see the placement options ...
Manage Opening Connections
Manage an Opening and its cut elements using the commands of the Connections grip. (Each Opening is associated to a single element, but a single Opening can cut multiple elements at once). Note: Opening geometry is measured relative to its associated element, and moves along with it. ...
Opening Listing Parameters
Parameter Short Description Long Description Center Height to Home Story For opening in Wall or Beam. Home Story is the same as that of the opening's associated element. Center Height to Project Zero For opening in Wall or Beam. ...