Model Display in the Section Window

Note: The controls for the display of elements is nearly identical for Elevations and Interior Elevations, and for 3D Documents based on the Floor Plan.

Controls of the Model Display panel in Section Settings define the appearance (fills, contours, surfaces) of:

Cut Elements

Uncut Elements

Sun and Shadows

Marked Distant Area

Element Contours at Section Boundary

in the Section window.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/SectionComposite.png 

The following are brief descriptions of these display features.

For an individual description of each control, see Model Display Panel.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/SectionModelDisplayAll.png 

Cut Elements

By default, cut elements are shown using their element-level line and pen definitions. You can customize the appearance of cut elements in a Section window by checking the Uniform Pen for Cut Elements checkbox in the Model Display Panel of Section Settings, then assigning the lines and colors, for the display of cut elements in this Section only.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/CutElements.png 

Uncut Elements

Surface colors and vectorial hatching can be displayed only on uncut surfaces of elements in the Section/Elevation/IE windows.

These options in the Model Display Panel of Section Settings enable you to apply surfaces (shaded or unshaded) to the uncut elements shown in the Section window:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/SectionEx5.png 

Sun and Shadows

The following elevation is displayed with Vectorial Hatching “on” (as shown by the brick wall) and with Sun Shadow “on” (as shown by the shadow cast by the roof overhang.)

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/VectorialShadow.png 

Another effect is to display uncut surfaces in “shaded” mode - that is, to reflect rounded contours. You can combine the two effects (cast shadows and shaded effect) in a single Section display:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/ShadowShaded.pnghttps://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/sHADEDmODEL.png 

Marked Distant Area

Consider the following Section line on the Floor Plan:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/SectionEx1.png 

Note that this Section includes the west face of the building, close to the section line, as well as parts of the far end of the building that extends northward. In this Section view, the close and distant areas are displayed identically, so you cannot tell which is which:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/SectionEx2.png 

To differentiate the “close” from the “distance” elements, reconfigure the section so that it contains a Marked Distant area: check the Marked Distant Area box in the in the Model Display Panel of Section Settings and specify a different color for the contours of the “distant” elements.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/SectionModelDisplay.png 

Return to the Floor Plan and notice that a new line segment representing the Distant Area has appeared.

Select this line and drag it as shown:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/DragDistant.png 

Note: The Distant Area line is a “Marker Range Line”.

See also Display of Marker Range Lines.

Now re-open the Section. The distant elements are distinguished from the closer ones.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/SectionEx3.png 

Element Contours at Section Boundary

“Element Contours” can be applied to elements shown in the Section, Elevation or Interior Elevation window which extend beyond the horizontal limits of the Section.

Use The Element Contours at Section Boundary settings from the Model Display Panel of Section Settings to define this boundary.

Here, the left edge of the wall on the left does not fall within the section, and the displayed parts are shown as unfinished, without contours.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/NoContours.png 

However, you can choose to display boundary contours - that is, to draw a line at the element’s boundary as it is shown in the section, even though the element does not really end there.

At Add Element Contours, choose “Own Contours” to display these contours using the uncut pen chosen for these elements in their own Settings dialog boxes; or “Override Contours” to use a pen of your choice:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/OverrideContoursSet.png 

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-24-reference-guide/050_viewsvb/OverrideContours.png 

  • Was this Helpful ?
  • YesNo
Relevant topics
Column Display on Floor Plan and Section
Use the Floor Plan and Section page of Column Settings.   See Element Display in Floor Plan and Section. Hidden Lines Define Hidden Line attributes. Hidden Lines are used for Columns under Slabs if this is turned on at Model View Options. See Model View Options for Construction ...