|
Parameter |
Short Description |
Long Description |
|
|
Beam Axis Offset |
Reference line axis offset. |
By default, this value is zero (the reference axis runs down the center of the Beam). User may assign any other value as offset in Beam Settings: this offsets the reference axis by the given amount from the center. |
|
|
Beam Cross Section Type |
Regular or Complex. |
Shape of the Beam’s cross-section as defined in the Beam Settings dialog box. |
|
|
Beam End Surface |
Name of the Surface assigned to the two ends of the Beam. |
|
|
|
Beam End Surface Area |
Area of the Surfaces of both ends of the Beam |
|
|
|
Beam Hole Height |
Height or diameter of the first-placed hole in the Beam). |
Same value as Hole Dimension 2 or Diameter, on the Hole panel of Beam Tool Settings |
|
|
Beam Hole Level |
Distance of the centerpoint of the first-placed hole from the edge of the Beam |
Same value as Position, on the Hole panel of Beam Tool Settings. |
|
|
Beam Hole Number |
Total number of holes in the Beam. |
|
|
|
Beam Hole Width |
Width of the first-placed hole in the Beam |
Same value as Hole Dimension 1, on the Hole panel of Beam Tool Settings. |
|
|
Beam Holes Edge Surface |
Total edge area of all Beam holes |
|
|
|
Beam Holes Surface Area |
Total area of the 2D Surface of all holes, as calculated on one Side of the Beam. |
|
|
|
Beam Holes Volume |
Total volume of all holes in the Beam . |
Multiplies Beam Width by Holes Surface Area. |
|
|
Beam Left Side Surface |
Name of the Surface assigned to the left Side of the Beam. |
"Left” and “Right” are determined based on the direction of the Beam’s reference axis. The axis direction is the direction in which you drag the cursor to draw the Beam. |
|
|
Beam Left Side Surface Area |
Area of the Surface of the left Side of the Beam |
reduced by any SEO’s or holes "Left” and “Right” are determined based on the direction of the Beam’s reference axis. The axis direction is the direction in which you drag the cursor to draw the Beam. |
|
|
Beam Length Left |
Length of the Beam on its left Side. |
"Left” and “Right” are determined based on the direction of the Beam’s reference axis. The axis direction is the direction in which you drag the cursor to draw the Beam. |
|
|
Beam Length Right |
Length of the Beam on its right Side. |
"Left” and “Right” are determined based on the direction of the Beam’s reference axis. The axis direction is the direction in which you drag the cursor to draw the Beam. |
|
|
Beam Right Side Surface |
Name of the Surface assigned to the right Side of the Beam. |
"Left” and “Right” are determined based on the direction of the Beam’s reference axis. The axis direction is the direction in which you drag the cursor to draw the Beam. |
|
|
Beam Right Side Surface Area |
Area of the Surface of the right Side of the Beam |
reduced by any SEO’s or holes "Left” and “Right” are determined based on the direction of the Beam’s reference axis. The axis direction is the direction in which you drag the cursor to draw the Beam. |
|
|
Bottom Surface |
Name of the Surface assigned to the bottom of the Beam. |
|
|
|
Bottom Surface Area |
Area of the Surface of the bottom of the Beam |
reduced by any SEO’s or holes. "Left” and “Right” are determined based on the direction of the Beam’s reference axis. The axis direction is the direction in which you drag the cursor to draw the Beam. |
|
|
Top Surface |
Name of the Surface assigned to the top of the Beam. |
|
|
|
Top Surface Area |
Area of the Surface of the top of the Beam |
reduced by any SEO’s or holes. |
|
