Snap Guides

 Snap Guides are temporary lines and arcs that appear along existing elements, to assist accurate element placement.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/030_interaction/GuidelinesNFG2.png 

Unlike Guide Lines, Snap Guides are temporary and disappear automatically when the cursor is no longer in the vicinity. However, you can make a Snap Guide remain in place by pinning it.

You can also control which Snap Guides appear by marking particular points or edges as Snap References.

See the sections below on how to use Snap Guides:

Lock Input to Snap Guide

To constrain your input to the desired Snap Guide, do one of the following:

Press Shift during input

From the context menu, use Lock to Guide Line/Snap Guide

Turn Snap Guide Function On/Off

To activate/deactivate Snap Guides, do one of the following:

Click the Snap Guides and Points toggle from the Standard Toolbar

Use the Snap Guides command in the toolbar dropdown

Use View > Snap Guides

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/030_interaction/SnapGuideToolbar.png 

Activate Snap References

To make Snap Guides appear in more places that are relevant to your input, you can define any edges or points as Snap References.

Activate a Snap Reference (a dynamically appearing blue highlight) by hovering the cursor over element edges or points:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/030_interaction/SnapGuide.png     https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/030_interaction/SnapPoint.png

You can activate any number of Snap References simultaneously. Once you have defined Snap References, you will see additional Snap Guides appear which are relevant to those References as well as your current input vector.

See Appearing Snap Guides.

Again, to lock your input vector to any Snap Guide, press Shift.

Snap References stay in place, even if you move the cursor away, until you do one of the following:

Complete input

Click ESC

Hover over the existing Snap Reference until it disappears, or click Q (see Force Snap Reference (Shortcut), below).

Force Snap Reference (Shortcut)

Click Q on any edge or point to “Force Snap Reference”, to highlight an edge or node as a Snap Reference instantly (regardless of the timer set in the Work Environment).

Note: The predefined Shortcut for this command is the Q key, but may vary depending on your localized version of ARCHICAD.

Appearing Snap Guides

During input, Snap Guides will pop up automatically and temporarily.

Which Snap Guides will appear?

Snap Guides which are relative to the location of your cursor (e.g. Horizontal/Vertical, Parallel to Grid, a fixed Incremental Angle), depending on the options set at Options > Work Environment > Input Constraints and Guides.

Snap Guides relative to any Snap References you have marked, and to the relations among those Snap References.

Where applicable, icons on the Snap Guide indicate the relation:

Tangent

Parallel

Perpendicular

Angle Bisector (if applicable)

The line connecting two circles’ centerpoints (if applicable)

Pin or Place a Snap Guide Manually

Unlike the automatically appearing Snap Guides, a pinned or explicitly placed Snap Guide is infinitely long and will remain visible, without fading out, until input is complete - even if you move the mouse away.

To pin a Snap Guide so that it does not disappear until input is complete, or to place one manually, do one of the following:

From the context menu of an existing Snap Guide, use the Pin Snap Guide command:

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/030_interaction/PinSnapGuideContext.png 

From the context menu during element input, use the Place Snap Guide/Snap Circle command:

Placehttps://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/030_interaction/SnapGuide.png 

During Tracker input, click the crosshair icon in the coordinate field. The edited element will then jump to that coordinate value and the applicable Snap Guides will appear.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/030_interaction/DistanceCrosshair1.png   https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/030_interaction/DistanceCrosshair2.png

Options for Snap Guides and Snap References

Options for Snap Guides/References are set at: Options > Work Environment > Input Constraints and Guides.

The color of the Snap Reference is the same as the Snap Guide color.

https://helpcenter.graphisoft.com/wp-content/uploads/archicad-23-reference-guide/030_interaction/SnapGuideColor.png 

  • Was this Helpful ?
  • YesNo
Relevant topics
Snap (1D to 1D)
The Snap adjustment is available only to adjust a 1D Member to another 1D member, “one to the other” only. Snap connects a 1D Member to another nearby 1D Member node, if the Members are not in the same plane. The Snap adjuster combines stretch, offset and rotation. This can be ...