선직곡면형 쉘 편집 옵션

선직곡면형 쉘은 두 개의 프로파일을 가집니다. 첫 번째 프로파일의 한쪽 끝은 더 큰 핫스팟에 의해 구별됩니다; 쉘의 바닥 높이를 나타냅니다.

여기에 양쪽 프로파일에 할 수 있는 몇 가지 편집 기능이 있습니다:

프로파일 계속하기

예를 들어, 직선 프로파일을 늘여서 쉘의 그 쪽 끝을 넓게 만듭니다.

https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/ContinueProfileRuled.png     https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/ContinueProfileRuled2.png

곡선 테두리

https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/CurveEdgeRuled1.png     https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/CurveEdgeRuled2.png

프로파일 드래그하기

이 명령을 사용하여 자신의 면 안에서, 수평 그리고/또는 수직 방향으로 프로파일을 새 위치로 드래그합니다.

https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/DragProfile1.png     https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/DragProfile2.png

프로파일 회전하기

이 명령을 사용하여 선택한 프로파일을 공간에서 회전시킵니다.

https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/MirrorShell1.png     https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/MirrorShell2.png

프로파일 면 올리기

여기서 프로파일 면 전체를 수직 방향으로 움직입니다.

https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/ElevateProfile.png     https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/ElevateProfile2.png

수평으로 프로파일 늘이기

여기서는 프로파일 면을 들어 수평으로 드래그합니다.

https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/DragProfileHoriz1.png     https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/DragProfileHoriz2.png

프로파일 면 변환하기

https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/TurnPlane1.png 

클릭하여 변환점을 입력합니다. 그 다음 커서를 움직여 변환 방향을 정의하고 클릭하여 완료합니다.

https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/TurnPlane100170.png   https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/TurnPlane2.png   https://helpcenter.graphisoft.com/kr/wp-content/uploads/sites/7/archicad-24/040_elementsvb/TurnPlane3.png

  • Was this Helpful ?
  • YesNo