Stair Tool Basics - Open Stringer Stairs

Gordana Radonic
Community Manager
Community Manager

In this article we are going to create an Open Stringer Stair.

 

wp-content_uploads_2017_09_Open-Stringer-Stairs-1024x773.png

 

To achieve this type of Stair structure, we will choose 'Beam' structure for the flight (and landing).

wp-content_uploads_2017_09_OS-Stair-Structure-923x1024.png
For the opposite edge of the Stair add Stringer by ticking the box, optional 'Stringer Left' or 'Stringer Right'. Stringers setting will appear under 'Structure' tree menu.

 

In the 'Beam – Flight' structure settings choose 'Open Stringer 21' as a Beam type.

 

wp-content_uploads_2017_09_Open-Stringer-Beam-flight-1024x679.png

 

Under 'Beam Component Settings', choose to place Open Stringer beam in a relation to center line, right or left side in 'Beam 1 Offset from' setting.

With 'Beam 1 Position X' setting one can specify the value of the offset. The -/+ directions of the offset are illustrated on the scheme above these settings.

 

wp-content_uploads_2017_09_Open-Stringer-Beam-Offset-1024x1009.png

 

If there is a nosing detail used for the treads, slight offset for the Open Stringer beam from the Stair boundary is needed. In this case, we will set 'Right side', -15 mm for the offset (exact value of the nosing thickness) and for the 'Beam 1 Anchor' point choose 'Top right' as that would be the point to measure offset from.

 

wp-content_uploads_2016_06_Info_18x18.png
NOTE: If choosing 'Profiled Flight Beam' or 'Profiled Stringer Beam' which are using custom beam profiles, beside 'Top Left', 'Top Middle' and 'Top Right' anchor point, one can choose 'Profile origin' as well.

 

Under 'Stringers - Flight' settings choose between 'Flight Stringer 21' or 'Profiled Flight Stringer 21' if you want to use any custom beam profile.

wp-content_uploads_2017_09_Open-Stringer-Stringer-Settings-1024x733.png

This type of the Stairs is usually made as a winder type so under 'Stair setting' in 'Geometry and Positioning' we will choose 'Winder with Equal Angles' and under Winder option set 'Fixed Number of Goings' to 3.

 

wp-content_uploads_2017_09_Open-Stringer-Winder-Options-1024x610.png

 

After making all the settings in Stair Selection Settings, we can construct our stair. If needed, adjustment of the Open Stringer at winder turning will be done.

  • Select the Stair, click Edit and Select Open Stringer structure.
  • From the context menu by pressing right click, choose 'Split Stair Structure'.
  • Split the structure of the Open Stringer at the turning point and geometry will be displayed correctly.
wp-content_uploads_2017_09_Open-Stringer-Editing-of-the-Stringer-1024x260.png

Risers should be manually shortened for the same value of the tread nosing width. The easiest way to edit risers is in edit mode on the Floor plan using the help of the guide line placed parallel to the stair edge, but same can be achieved in a 3D View as well. If the Stair has turning like in our example, additional editing of the treads might be needed.

 

wp-content_uploads_2017_09_Open-Stringer-Editing-Riser-1024x579.png

 

After finishing the construction of the Stair, use Railing tool to add appropriate railing and even paneling on the wall side to achieve the complete design of the stair.

Check the ARCHICAD YouTube Channel for tutorials about the Railing Tool and the Stair Tool.

Still looking?

Browse more articles

Back to articles

See latest solutions

Accepted solutions

Start a new discussion!